A garbage disposal that's been making grinding sounds for months before stopping entirely often has a seized bearing or cracked impeller โ signs the motor isn't worth repairing. Our techs in Argyle tell you honestly whether a repair or a same-day unit swap makes more financial sense.
๐ Call +1-855-718-1500 โ Same-Day Service
Garbage disposal failures have specific, diagnosable causes. Our techs don't just swap units โ they identify what failed and whether repair or replacement is the right call for your situation.
Hum but no spin: jammed impeller. No sound at all: tripped thermal overload or failed motor. Intermittent operation: loose wiring at the switch or disposal unit. Continuous drain from the sink collar: failed sink flange gasket. Leak from the side: dishwasher drain hose connection or internal body crack. We trace the symptom to the specific cause before recommending any solution.
InSinkErator (Badger, Badger 5, Compact, Evolution series), Moen GXS/GX series, Waste King, KitchenAid, and Whirlpool disposals all mount differently and have specific jam-clearing procedures. We know the mounting assembly for each brand and carry the correct jam-clearing wrench sizes.
A disposal that jams once is worth clearing and resetting. A disposal that jams repeatedly, has a seized turntable bearing, emits burning smells, or is over 10 years old is likely approaching motor failure โ and the repair cost of a failed motor exceeds the cost of a new unit.
A disposal installed without properly removing the dishwasher drain knockout plug is a common installation error that floods the dishwasher interior. We check this and correct it if present.
From a simple jam clear to a full replacement with drain reconnection, here's how we handle each garbage disposal scenario in Argyle, TX.
If the jam-clearing wrench won't budge the impeller, the motor shaft may be seized rather than just stuck from debris โ we distinguish between the two before recommending replacement.
If power is confirmed at the disposal and it still won't start after a reset, the motor is failed. We then move to the replacement conversation with honest cost comparison.
We identify the leak source before recommending any repair. A sink collar re-seal is a 30-minute job. A unit with a cracked body has no cost-effective repair and warrants replacement.
If the turntable bearing has failed โ indicated by a loud rumbling throughout operation rather than specific impact sounds โ that's an internal motor wear failure that warrants replacement.
A disposal that grinds normally but drains slowly has a blockage in the drain arm or p-trap โ not an internal disposal problem. Food particles and grease accumulate in the short drain arm between the disposal outlet and the p-trap. We disconnect and clean the drain arm, clear any p-trap buildup, and reinstall with clean connections.
Replacement includes: safely disconnecting electrical at the junction box under the sink, removing the old unit and mounting assembly, installing the new unit with correct wiring and plumbing connections, testing for full jam-free operation, and verifying zero leaks at all connections before leaving.
A disposal call takes 30โ60 minutes in most cases. Here's exactly how it goes โ from your first call to a clean, functional kitchen drain.
If you know the disposal is over 10 years old, tell us โ that changes how we approach the repair-vs-replace conversation upfront.
For leaks, we dry the area completely and run a short test cycle to confirm exactly which connection is dripping.
You decide. We don't upsell replacement when repair is the right answer, and we don't push a cheap repair that won't hold on a unit that's genuinely at end of life.
We leave the cabinet dry and the disposal running quietly. If a dishwasher drain hose was involved, we run a dishwasher cycle to verify no backup occurs.

The disposal under our kitchen sink was 12 years old and started leaking from the bottom โ which the tech explained is always an internal seal failure, not a repairable condition. He had a replacement 3/4 HP InSinkErator on his truck, installed it in about 45 minutes, and the kitchen is back to normal. Old unit got pulled, new unit tested clean, no leaks at any connection.
After we added a dishwasher, it started backing up every cycle. Masters Plumbing Service found the problem immediately โ the previous installer had forgotten to knock out the dishwasher drain plug inside the disposal inlet. The plug was blocking the drain port. Two-minute fix. The tech also tightened the dishwasher drain hose clamp, which was loose. Never had another backup.
Disposal leaking from the sink collar area. Previous owner had installed it with silicone instead of plumber's putty at the flange โ silicone doesn't hold the mounting pressure correctly and had separated. Tech re-seated the flange with putty, re-tightened the mounting ring, and the leak stopped. Tested with a full minute of running water. All clear.

Masters Plumbing Service dispatches garbage disposal repair and replacement technicians throughout Argyle and the broader Argyle, TX service area. Most calls are same-day โ call to check today's availability.

Call now โ same-day service available in Argyle and across Argyle, TX.
๐ Call +1-855-718-1500 Now